Dacor CM24P-1 Guía para resolver problemas descargar pdf (Pagina 33)

Turning Pre-brew On and Off:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Pre-brew” appears on the display.

2. Push the MENU button.

3. Repeatedly push the MENU button to see the pre-brew status for each drink. Stop on the drink for which you want to turn pre-brew on or off.

4. Push the UP or DOWN buttons to select “Yes” or “No”.

5. Push the SET button to make the change.

6. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Turning Tamping On and Off:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Tamping” appears on the display.

2. Push the MENU button.

3. Repeatedly push the MENU button to see the tamping status for each drink. Stop on the drink for which you want to turn tamping on or off.

4. Push the UP or DOWN buttons to select “Yes” or “No”.

5. Push the SET button to make the change.

6. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Changing the Used Coffee Ground Bin Meter:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Grounds Number” appears on the display.

2. Push the MENU button.

3.To adjust the number of grounds detected in the bin before the “Drawer Full” message appears on the display, push the UP or DOWN buttons. The default

setting is 20.

4. Push the SET button to change to the new ground number.

5. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Milk Cleaning Warning Time:

Pre-set at the factory to 2 hours. Do not change.

Routine Cleaning Warning Time:

Pre-set at the factory to 50 cycles. Do not change.

Group Setting:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Group” appears on the display.

2. Push the MENU button.

3.If the group number is not set to 2.0, push the UP or DOWN buttons until the display shows a group setting of 2.0. The coffee system will not work properly set

to any other value.

4. Push the SET button.

5. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Changing the Grinder Setting Warning:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Grinder Setting” appears on the display.

2. Push the MENU button.

3. To adjust the amount of drinks prepared before the “Grinder Setting” message appears on the display, push the UP or DOWN buttons. The default is 250.

4. Push the SET button to change the grinder setting warning.

5. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Changing the Coffee Temperature:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Coffee Temperature” appears on the display.

2. Push the MENU button.

3. To adjust the coffee temperature, push the UP or DOWN buttons. The default is 98°C.

4. Push the SET button to change the temperature setting.

5. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Changing the Steam Temperature:

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Steam Temperature” appears on the display.

2. Push the MENU button.

3. To adjust the coffee temperature, push the UP or DOWN buttons. The default is 125°C.

4. Push the SET button to change the temperature setting.

5. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

Changing the Water Filter Warning:

If you install a water filter to lower the hardness of the water supplied to your coffee system, you can program the system to warn you when you need to change

the filter cartridge. Check the manufacturer instructions for the filter cartridge capacity. Enter the filter capacity into the coffee system in liters (3.8 liters = 1

gallon).

1. With the main programming menu accessed, push the UP or DOWN button repeatedly until “Water Filter” appears on the display.

2. Push the MENU button.

3. To adjust the number of liters used by the coffee system before the “Water Filter” message appears on the display, push the UP or DOWN buttons.

4. Push the SET button to accept the clean warning number entered.

5. Push the UP or DOWN button repeatedly to select another feature to change or close the front panel door to exit the main programming menu.

PG: 33

1 2 ... 28 29 30 31 32 33

Comentarios a estos manuales

Sin comentarios

Dacor CM24P-1 Guía para resolver problemas Pagina 33

Comentarios a estos manuales

Relacionado con productos y manuales para Cafeteras Dacor CM24P-1